![]() Specifies up to 10 stores to use with Citrix Receiver. You can specify the command as follows :CitrixReceiver.exe ALLOWADDSTORE=NTo provide the address for the store just follow the option below and the sample command line is given :Use this option to specify the Store name.Not applicable if Citrix Receiver is installed per user. A – Allow users to add or remove both secure stores (HTTPS) and non-secure stores (HTTP).S – Allow users to add or remove secure stores only (configured with HTTPS).N – Never allow users to add or remove their own store.Specifies whether users can add and remove stores not configured through Merchandising Server deliveries users can enable or disable stores configured through Merchandising Server deliveries, but they cannot remove these stores or change the names or the URLs.) Defaults to S. You can use the following switch :ĬitrixReceiver.exe /AutoUpdateCheck=disabled Usually I prefer to disable the Auto update in a managed environment. Note that users must log off and log back on to their devices after an installation with single sign-on authentication enabled. ![]() This property is required for smart card single sign on. Enables single sign on when /includeSSON is also specified. Įnable SSO : Enable single sign on when /includeSSON is specified. This option is required for Smart card single sign on. Install SSO authentication : Install Single Sign On Authentication. Windows Aero Support : Enables the Windows Aero experience (for operating systems that support it).Ĭombining all the option above you get the following command : ADDLOCAL=ReceiverInside,ICA_Client,SSON,AM,SELFSERVICE,USB,DesktopViewer,Flash,Vd3d,Webhelper NET 3.5.Īuthentication Manager : Installs the Authentication Manager. The Self-Service Plug-in is not available for Windows Thin PC devices, which do not support. NET 3.5 Service Pack 1 must be installed on the user device. The AM value must be specified on the command line and. Self Service: Installs the Self-Service Plug-in. Media Stream for Flash : Install HDX media stream for Flash. ĭesktop Viewer : Installs the Desktop Viewer. It requires Admin rights to install and enable. ![]() SSON: Indicates that the Citrix Receiver for Windows will be installed with the single sign-on component. In addition, it verifies environment parameters and shares them with storefront (similar to ICO client detection). This component retrieves the ICA file from the storefront and passes it to the HDX engine. Web Helper : Installs the web Helper component. When you upgrade Citrix Receiver for Windows from 13.x (non-Enterprise) or 4.1 to Version 4.2 or later, the /RCU switch is not required and ignored To upgrade from the command line, run the following command: However, Receiver clean-up does not run by default when you upgrade from the command line. When you upgrade Citrix Receiver Version 13.x Enterprise or 12.x to Citrix Receiver for Windows Version 4.4 and later using the graphical user interface, the installer runs the Receiver clean-up (RCU) utility by default. Upgrade from old receiver version : Allows you to upgrade from an unsupported version to the latest version of Citrix Receiver. Silent installation : Disables the error and progress dialogs to run a completely silent installation. Įnable CEIP : When you enable participation in the Citrix Customer Experience Improvement Program (CEIP), anonymous statistics and usage information are sent to Citrix to help Citrix improve the quality and performance of its products. To disable dynamic client name support, set this property to No and specify a value for the CLIENT_NAME property. When users change their computer name, the client name changes to match. Set Client Name: The dynamic client name feature allows the client name to be the same as the computer name. If you supress reboot prompts, any USB devices which are in suspended state when Citrix receiver for windows installs will not be recognised by the Citrix receiver for windows until after the user device is restarted. This option is not necessary during Silent install. Supress reboot: This option supress reboot during UI installs. So when we migrated from Xenapp 6.5 to Xen desktop 7.1.15 we needed to upgrade the receiver to latest version. This was also one of the main challenges in our organisation since we were use using Citrix Online plugin version 12.1. We also need to be able to uninstall the old unsupported receiver from the client system and then install the new one. Now there are few terms we should understand before we put that into script to install receiver. We need to be able to provide all the functionality to the user without him having to open Google Chrome, Internet explorer or Citrix receiver. We are deploying Citrix Receiver through SCCM and we will enable Single sign on so that user does not have to enter the credentials to connect to Citrix Store front.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |